Online Keyboard Tester Tool

Test every key on your keyboard in seconds: see which keys register, how many work at the same time (NKRO), whether any key double types, and how fast rapid trigger and SOCD / Snap Tap respond on Hall effect keyboards. Free, nothing to install.

Pro Keyboard Tester

Press every key. Tested keys turn green, so any key that stays dark isn’t registering.
Click here or press any key to start
0 / 0
Keys tested
0
Held now
0
Max at once
0
Total presses
0
Possible chatter
Other keys
Hall effect tests Made for rapid trigger and SOCD keyboards, but they work on any keyboard.
Rapid trigger tap test
Tap one key as fast as you can for 5 seconds. Rapid trigger resets the key as soon as it starts rising, so the release gap gets shorter. Compare keyboards or rapid trigger settings.
Best: —
—
Taps
—
Taps/sec
—
Peak/sec
—
Avg press
—
Min release
SOCD / Snap Tap test
SOCD (Snap Tap, Snappy Tappy) means that when two opposite keys are held, only the last one pressed counts. Keyboards do the swap in a millisecond or two, faster than any finger, so the test can tell it apart from you.
Hold A, then press and release D while still holding A. Repeat a few times.
Overlaps: 0 · Instant swaps: 0
Last keys
Nothing yet. Press a key.
How to read the results
Max at once: hold as many keys as you can. If a key you’re holding doesn’t light up, the keyboard has a rollover limit (6KRO is common on office keyboards) or that combination ghosts. Most gaming keyboards register every key (NKRO).
Possible chatter: a key that fires again within 20 ms of being released is outlined in red. That usually means a worn or dirty switch. Very fast tapping on rapid-trigger Hall effect keyboards can occasionally trip it too.
Can’t be tested here: the Fn key (it’s handled inside the keyboard) and system shortcuts like Alt+Tab. On Windows, AltGr also lights up the left Ctrl key.
Gaming check: hold W A S D + Space together and make sure all five light up.

How to use the keyboard tester

The tester runs in your browser and works with any wired, wireless or laptop keyboard on Windows, macOS, Linux and ChromeOS. Nothing is installed, and the keys you press never leave your computer.

  1. Start the testClick the tester or just press any key. The border glows green while it is capturing your keys.
  2. Press every keyEach key turns green once it registers. A key that stays dark is not being detected.
  3. Hold keys togetherPress several keys at once and watch Max at once to check rollover and ghosting.
  4. Stop when doneClick anywhere outside the tester, or press Esc three times, to give your keyboard back to the page.

Use the Full size / TKL and ANSI / ISO buttons to match the drawing to your keyboard. On a non-QWERTY layout such as AZERTY or QWERTZ, Chrome and Edge label the keys with your own layout. Keys that are not on the drawing, such as media keys, show up under Other keys.

What this keyboard tester checks

Key test

Every key registers

Press each key once. The counter shows how many of the keys on the drawing you have tested, and the log lists every press with its key code and how long you held it.

Good result: every key turns green, and each press shows up once in the log.

Rollover

Many keys at once (NKRO)

Hold as many keys as you can. Max at once shows how many the keyboard reports together. For gaming, hold W A S D + Space + Shift.

Good result: every key you hold lights up at the same time.

Chatter

Double typing and switch chatter

A key that fires again within 20 ms of being released is outlined in red and counted under Possible chatter. Nobody can press a key that fast, so it points to a worn, dirty or faulty switch.

Good result: Possible chatter stays at 0 while you type normally.

Hall effect

Rapid trigger and SOCD / Snap Tap

Two extra tests for magnetic Hall effect and TMR keyboards measure how fast a key resets and whether the keyboard handles opposite keys (SOCD). They work on any keyboard, so you can compare.

See how to read them below.

Keyboard ghosting test: NKRO vs 6KRO

Key rollover is how many keys a keyboard can report at the same time. When you go past that limit, extra keys are ignored. Ghosting is a related fault where pressing a few keys makes a different key appear that you never pressed. Hold different combinations and watch the drawing: a key you are holding that stays dark, or a key lighting up that you are not touching, shows the limit.

RolloverKeys at onceWhere you find it
2KRO / 3KRO2 to 3, some combinations failCheap membrane and older office keyboards
6KRO6 keys plus modifiers (Ctrl, Shift, Alt, Win)Many office and laptop keyboards, and some gaming boards in a compatibility mode
NKROEvery keyMost mechanical and Hall effect gaming keyboards

6KRO is plenty for typing. For games, check the keys you actually hold together, such as movement plus jump, crouch and an ability key. If a gaming keyboard stops at 6, look for an NKRO setting in its software or a key combination in the manual.

Rapid trigger and SOCD (Snap Tap) tests

Hall effect, TMR and other magnetic keyboards measure how far each key is pressed, which enables two gaming features you can check here. To learn how they work, read our guides to Hall effect keyboards and TMR vs Hall effect sensors.

Rapid trigger tap test

Rapid trigger resets a key as soon as it starts moving up, instead of waiting for a fixed reset point, so you can tap again without lifting your finger all the way. Press Start tap test, then tap one key as fast as you can for 5 seconds.

  • Taps/sec and Peak/sec show your speed over the whole test and at its fastest moment.
  • Min release is the shortest time the key was up between two taps. Rapid trigger makes this gap smaller, so it is the number to compare between keyboards or settings.
  • Run it a few times with rapid trigger on and off, or with different sensitivity values, and compare the best results.

SOCD / Snap Tap test

SOCD (also called Snap Tap or Rappy Snappy) decides what happens when you hold two opposite keys. With SOCD on, only the last key you pressed counts, so changing strafe direction is instant. Hold A, press and release D while still holding A, and repeat a few times.

  • SOCD is ON when the keyboard swaps the keys within a few milliseconds, faster than any finger. These swaps show as yellow lines on the timeline.
  • SOCD is OFF when both keys stay down together. The overlap shows as an orange area.

Some games, such as Counter-Strike 2 on Valve’s official servers, do not allow SOCD features. Use the test to make sure it is off before you play those games. Read more in our Rappy Snappy and SOCD guide.

Want these two tests without opening this page? The free Rapid Trigger & SOCD Tester runs offline as a browser extension or a Windows app.

Fix common keyboard problems

A key is not working

  1. Press the key in the tester. If it lights up here, the keyboard is fine and the problem is a setting in your game or app.
  2. If it stays dark, try another USB port, unplug any USB hub, and for wireless keyboards charge them or try the cable.
  3. Remove the keycap and blow out dust or crumbs. On hot-swap keyboards, swap the switch with a working one to see if the switch or the socket is the problem.
  4. If the same key also fails on a second computer, the keyboard needs repair or replacement.

Keyboard double typing (chatter)

When one press types two letters, the tester flags it as possible chatter. The usual causes are dust under the switch, a worn mechanical contact, or a debounce setting that is too low. Clean the switch with compressed air, raise the debounce time in the keyboard software if it has one, update the firmware, and on hot-swap keyboards replace the switch. We cover a real example in fixing the Keychron double key press issue. Hall effect and TMR switches have no metal contacts to wear out, which is one reason people switch to them; see Hall effect vs mechanical switches.

Keys pressed together are missed

Run the ghosting test above. If the keyboard stops at 6 keys or drops certain combinations, turn on NKRO in its software, or choose a keyboard that supports it.

Hall effect keys act on their own

Keys that trigger by themselves, or keys that feel too sensitive, usually need calibrating. Run the calibration in the keyboard’s software, keep magnets and phones away from the board, and avoid a very small actuation point or rapid trigger sensitivity on keys you rest your fingers on.

Keys that cannot be tested in a browser

The Fn key is handled inside the keyboard and never reaches the computer, and shortcuts such as Alt + Tab or Win + L are taken by the operating system first. On Windows, AltGr also lights up the left Ctrl, and Print Screen only reports its release, so it shows as a release-only press in the log.

Keyboard tester FAQ

Is this keyboard tester free and safe?

Yes. It is free, needs no download, and runs entirely in your browser. Your key presses are not stored or sent anywhere.

How do I check if all my keyboard keys work?

Click the tester and press every key once. Each working key turns green and the counter at the top shows how many you have tested. Any key that stays dark is not registering.

How do I test my keyboard for ghosting?

Hold several keys at the same time, especially the ones you use together in games, and check that every one lights up. If a held key stays dark, or a key you are not touching lights up, the keyboard has a rollover limit or ghosting.

What is the difference between NKRO and 6KRO?

A 6KRO keyboard reports up to six normal keys at once plus modifiers like Shift and Ctrl. An NKRO keyboard reports every key you press, however many. Most gaming keyboards are NKRO, and the Max at once counter shows which one you have.

Why does my keyboard type letters twice?

That is switch chatter, usually caused by dust or a worn switch. The tester flags any key that repeats within 20 ms of being released. Cleaning the switch, raising the debounce time, or replacing the switch normally fixes it.

Can I test rapid trigger online?

Yes. Use the rapid trigger tap test above: tap one key as fast as you can for 5 seconds, then compare taps per second and the minimum release gap with rapid trigger on and off.

How do I know if Snap Tap or SOCD is on?

Hold A, then press and release D while still holding A. If the keyboard swaps the two keys instantly, the tester shows SOCD / Snap Tap is ON. If both keys stay down together, SOCD is OFF.

Can this test keyboard latency or polling rate?

No. A browser only sees key presses after the operating system has processed them, so it cannot measure a keyboard’s real input latency or polling rate. For measured latency results, see our list of the lowest latency keyboards.

Does it work on a laptop, Mac or tablet?

Yes. It works with laptop keyboards and on macOS, where Option and Cmd are labelled for you. On a phone or tablet, connect a physical keyboard; on-screen keyboards do not send the same key events.

More keyboard guides and tools